CT6000, PC300/210 Nireco- hệ thống kiểm soát in cắt Nireco

Liên hệ:
Liên hệ
Mã sản phẩm:
PG1800 NIRECO
Hãng sản xuất:
Nireco
Xuất xứ:
Japan
Tình trạng:
Mới 100%
Mô tả:
Hệ thống kiểm soát in cắt CT6000, PC300/210 Nireco Việt Nam, đại lý Nireco Việt Nam, hãng Nireco tại Việt Nam, cảm biến Nireco
Chia sẻ:
Số lượng
Yêu cầu gọi lại
số điện thoại

Đại lý Nireco

Hệ thống kiểm soát in cắt Nireco Việt Nam

 

Overview

Unrivaled Reliability and Operability!

Introducing the Print-to-cut Register Control System

From small food wrapping machines to large offset rotary presses, print-to-cut register control system Cutmatic CT6000 features cut positioning control of any sheeter and folder, face-back matching, pre-print sheeting, and overprint. Significant improvements in performance have been achieved through high-speed processing and the ability to select the optimum control mode (Control A, B and C) for each web operation. Implementing a LCD touch panel that functions as both a display and a means of inputting data has simplified the panel, improving operability.

Feature

  • Mark search function
    The mark search function recognizes part of a pattern as a mark using a time-tested conventional controller.

  • LCD touch panel both enables operation and shows information
    The LCD touch panel enables the data necessary for an operation to be entered, and displays various parameters, gate mark waveforms, deviations, repeat lengths and other information. The color screen makes it easy to understand the operating status of the controller.

  • A panel designed with operability in mind
    The frequently-used motor operation switch has a user-friendly design that maintains a conventional sheet switch, which enables finger operation by the operator. This has also reduced the frequency with which the touch panel is used, extending its life.

  • High processing speed
    A single-chip microprocessor guarantees high-speed processing. (50% UP)

  • Fail-safe circuit
    The system automatically stops, reducing paper waste, when normal operation is impossible such as when signals from the sensor cannot be detected or when the web speed slows down.

  • Built-in check function
    The controller is equipped with a self-diagnostic function to verify operation in the event of a breakdown. As the line speed and the encoder pulse count can be displayed, the user can check whether the encoder is functioning normally and identifying malfunctioning areas has become easier than ever before.

  • Deviation display and output
    By displaying the measured deviation rate (cutting discrepancy) on the touch panel as a graph, movements in the print-to-cut register can be instantaneously confirmed. It is also possible to record the deviation rate by analog voltage. (±5V DC)

CT6000 Nireco

Configuration

System Diagram

 

 

web_ct6000_2nd.jpgController

Operating under microprocessor control, the controller processes electric signals from the scanning head and the encoder. Control mode, gain, etc. can be set to control parameters. The correction motor is driven by controller correction signals.

Optical fiber sensor

web_ct6000_4th.jpg

The optical fiber sensor was developed to enable detection at a constantly stable level, further improving the detection capability of a conventional S/H (sample/hold) circuit. The sensor uses a halogen lamp, which produces a high color temperature, and provides an outstanding color rendition. The sensor is superb at detecting marks with pale color combinations and adapts well to special webs. The circuit has also been designed to extend the life of the lamp, which has increased 1.7 times (5,000 hours). All of these improvements have made the sensor extremely easy to use.

Nireco 

Nhà phân phối Nireco Việt Nam

Encoder

web_ct6000_5th.jpg

The encoder is an absolute no contact photoelectric unit that is directly connected to a cutter or plate cylinder drive shaft. It is controlled by the A, B and Z phases and monitors the synchronization and speed of the plate cylinder.

Correction Motor

web_ct6000_6th.jpg

The correction motor normally drivers the register roller (or the compensator roller) to adjust web length between the final control unit and the cutter in an inline configuration. The cutter mechanism is controlled using a correction motor to operate a differential gear.

Scanning Head

web_ct6000_7th.jpg

The Scanning head incorporates a silicon photo diode, lamp, lens assembly and amplifier. Scanning head signals undergo high-speed automatic processing in the controller microprocessor to ensure automatic compensation of fogging of the scanning head window due to ink smudges, paper dust or slight changes in register mark density.

Nireco Việt Nam, Power Guide Nireco Việt Nam, servo valve Nireco, PG1800 Nireco Việt Nam,

Junction Box

web_ct6000_8th.jpg

This terminal box relays signals between the scanning head and the controller. It houses the scanning head lamp drive circuit and the mark catch verification lamp. * Not required for optical fiber

CT6000, PC300/210 Nireco- hệ thống kiểm soát in cắt Nireco

Bình luận của bạn
*
*
 Captcha
Danh mục sản phẩmDanh mục sản phẩm
Hỗ trợ trực tuyến
Liên hệ tư vấn mua hàng
Thống kê truy cập
  • Trực tuyến:
    3
  • Hôm nay:
    634
  • Tuần này:
    4838
  • Tháng trước:
    11986
  • Tất cả:
    595757
Video ClipVideo Clip
CÔNG TY TNHH THƯƠNG MẠI VÀ DỊCH VỤ TĂNG MINH PHÁT

 VPĐD: Số 1, Đường số 27, Phường Hiệp Bình Chánh, Quận Thủ Đức, Tp.HCM

 Nhân viên kinh doanh: Lê Mỹ Duyên  (Ms.)

 Email:  sale07@tmpvietnam.com        Tel:  0914.981.967 - 0919.329.139

 VP tại Đức: Am Boscheler Berg 4a 52134 Herzogenrath

 Website: avantgarde-x.de

Chính Sách Mua Hàng

   Giao hàng miễn phí.

   Làm việc các ngày trong tuần.

   Thanh toán linh động.

    Bảo hành 12 tháng.

Bản đồ

Công ty Tăng Minh Phát

© 2017 Tangminhphat.com, all right reserved.

Thiết kế website www.webso.vn

Loading...

Back To Top